Tools You Need to Set Up a New Tub
Tools You Need to Set Up a New Tub
Blog Article
We've noticed the article involving Installing A Bathtub down the page on the web and figured it made sense to discuss it with you here.
Mounting a bath tub isn't exactly rocket science, but it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily available, the job can relocate speedily; if you have to open a wall to remove the old tub as well as place the brand-new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub and set in the new one. Make sure you have qualified yourself for the job and fit trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This short article will help you install a new bath tub in your washroom if you have actually already purchased a new tub and do not require to change the arrangement of your previous water supply pipelines.
Your devices and also product checklist should comprise the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Using the two wood boards under its feet, put the bath tub in the called for position. The wooden boards are useful in evenly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub up until the level checks out degree.
To set up faucets, fit all-time low of the outermost versatile tap port to the proper supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the supply of water as well as inspect all joints and brand-new pipework for leaks and tighten them if necessary. Load the tub and also check the overflow outlet and the regular electrical outlet for leakages.
Ultimately, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has been made use of at the very least when as this will certainly settle it into its final position.
Getting ready for the Setup
Firstly, the supporting structure provided with the bath needs to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bathroom and the tiling, causing difficulties with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to always load the bath tub with water before sealing, to permit the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into account this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly offered on the marketplace. It is advisable to fit the tiles utilizing waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious person who reads about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that topic was really helpful. Loved our entry? Please share it. Help someone else discover it. Thank you for your time. Kindly pay a visit to our blog back soon.
Start Now
Report this page